Lectrosonics UM190b Instrukcja Użytkownika Strona 1

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Akcesoria komunikacja Lectrosonics UM190b. Lectrosonics UM190b User Manual Instrukcja obsługi

  • Pobierz
  • Dodaj do moich podręczników
  • Drukuj
Przeglądanie stron 0
UM190B
UHF BELT-PACK TRANSMITTER
OPERATING INSTRUCTIONS
and trouble-shooting guide
LECTROSONICS, INC.
Rio Rancho, NM
Przeglądanie stron 0
1 2 3 4 5 6 ... 13 14

Podsumowanie treści

Strona 1 - UM190B

UM190B UHF BELT-PACK TRANSMITTER OPERATING INSTRUCTIONS and trouble-shooting guide LECTROSONICS, INC. Rio Rancho, NM

Strona 2 - INTRODUCTION

RF BYPASSING 2 WIRE MIC 3 WIRE MIC Some mics require RF protection to keep the radio signal from affecting the capsule, even though the transmitter

Strona 3 - UHF Belt-Pack Transmitter

UHF Belt-Pack Transmitter TROUBLESHOOTING Before going through the following chart, be sure that you have a good battery in the transmitter. It is imp

Strona 4 - CONTROLS AND FUNCTIONS

SPECIFICATIONS AND FEATURES Operating frequencies: 470 to 608 MHz RF Power output: 70 mW (nominal) Frequency stability: ±0.002% Deviation: ±15 kH

Strona 5

UHF Belt-Pack Transmitter SERVICE AND REPAIR If your system malfunctions, you should attempt to correct or isolate the trouble before concluding tha

Strona 6 - BATTERY INSTALLATION

LIMITED ONE YEAR WARRANTYThe equipment is warranted for one year from date of purchase against defects in materials or workmanship provided it was pur

Strona 7 - OPERATING NOTES

INTRODUCTION Thank you for selecting the Lectrosonics UM190B belt-pack transmitter. The UM190B combines over 80 years of engineering experience wi

Strona 8 - MICROPHONE CORD TERMINATION

UHF Belt-Pack Transmitter GENERAL TECHNICAL DESCRIPTION The UM190B transmitter is comprised of a number of functional sub-systems as shown in the blo

Strona 9 - UM190B INPUT JACK WIRING

CONTROLS AND FUNCTIONS LF ROLL-OFF ADJ ANTENNA OFF ON –20 0 LECTROSONICS UM190B LEVEL AUDIO LF ROLL OFF 35 150 75 Hz INPUT JACK The input on the UM1

Strona 10 - LINE LEVEL SIGNALS

UHF Belt-Pack Transmitter MODULATION LEDS Indicate the proper setting of the MIC LEVEL control. LEVEL LED — Flickers or glows when sufficient audio is

Strona 11 - TROUBLESHOOTING

BATTERY INSTALLATION The transmitter is powered by a 9 Volt alkaline or lithium battery. It is important that you use ONLY an ALKALINE or LITHIUM bat

Strona 12 - SPECIFICATIONS AND FEATURES

UHF Belt-Pack Transmitter OPERATING INSTRUCTIONS 1) Install a fresh battery according to the instructions on the previous page. 2) Insert the micr

Strona 13 - RETURNING UNITS FOR REPAIR

MICROPHONE CORD TERMINATION 1 2 3 45 VIEW FROM SOLDER SIDE OF PINS 0.3" 0.15" Heatshrink Tubing TA5F Connector Assembly Mic Cord Stripping

Strona 14 - LIMITED ONE YEAR WARRANTY

UHF Belt-Pack Transmitter UM190B INPUT JACK WIRING The wiring diagrams shown on the separate sheet represent the basic wiring necessary for the most

Komentarze do niniejszej Instrukcji

Brak uwag